adajohn010

       You will probably need to fill your doll's bookcase with a few books and there are many ways to craft small volumes. I will demonstrate with photos below just one way to make miniature doll books for now...

Glue additional titles and decorations to the outside of the doll book.

Supply List for Miniature Books:

• corrugated cardboard
• scrap magazine pages
• glue stick
• scissors

        The television depicted on the left below, has a picture pasted directly to the monitor and is much easier to craft. The television shown on the right includes an additional cardboard covered frame so that you can replace the picture by sliding it between the layers of cardboard. 

       Both flat screen T. V.s are weighted down with washers, carefully glued into each television's base.

       Cut three rectangles from cardboard, two from the corrugated cardboard and one flatter piece from the cereal box. All rectangles should be identical in size.

       Glue the two corrugated pieces together and paint one side with black acrylic paint. Let this side dry before continuing.

       Take the third rectangle cut from a cereal box, and measure approx. 1/4" from the outside of each edge. Use a ruler to draw the lines marking the measurement. Now cut out the inside of the flat screen T.V. monitor.

       Only glue three edges of the third rectangle to the other corrugated rectangular pieces, leaving the top edge of the flat screen T. V. open (see photo below). Leaving a gap at the top of your doll's television will allow you to slip pictures in and out of the screen to change what the doll's are watching. All of these should be neatly stacked on top of each other when you are finished. (see photo)

       Cut a long narrow base for your T. V. from the corrugated cardboard. This base rectangle should be slightly shorter in length than the actual screen. 

       Trace around a washer at each end of the stand and then carefully poke around the tracing with the tip of your scissors or get an adult to cut away this top circular layer with an Exacto knife. 

       Crush down the center cardboard filler with the washers and glue so that these metal pieces are level with the top layer of cardboard. Layer masking tape across the washers to keep them firmly in place. (see photo below.) Set aside the stand to continue with later, while it dries.

      Now trace around the flat screen television screen on top of the black craft foam twice. Cut out the tracing and hot glue these foam pieces to the front and backs of the toy T. V.s. If you have the kind of flat screen television where you can change out the pictures. You will need to repeat measuring and cutting out the frame 1/4" from the edges before gluing this piece of craft foam on top of the screen. If you have a simpler flat screen without the frame, like the one shown just below, you will only need to cover the front and back of the screen before pasting on the television's picture.

       Now you are ready to attach the stand to the flat screen monitor. Cover the stand's base the same way that you covered the screen by layering the top and bottom between craft foam. Cut an additional strip of cardboard to glue between the screen and base. 

       Carefully attach this small piece with hot glue at each end. For a larger flat screen, you may wish to attach these two elements together with a cut dowel rod.

       Now cover any remaining cardboard with the same black craft foam.

       Barbie's little boy loves cars and trucks, so I decided to replace a missing trailer from a small replica of a John Deere big rig with a toy chest. Now our doll can pretend to haul the toys away after an exhausting fun filled day!

       In order to make this playscale toy box, you will need to first acquire the front end of a semi-trailer truck. If you have small children this will not be difficult. If not, take a trip to your local Goodwill or resale and you will surely find one of these in no time at all.

       Next, you will need to recycle a bit of plastic trash or a small box for the back end of the big rig toy chest. Choose something that looks in the correct proportion to your truck parts.

       Fortunately my semi-trailer truck has a hole between it's wheels where I can easily fit a small wire to attach the toy chest. You can see this hole through the plastic recycled box above.

        After covering my toy chest with masking tape, I simply poked a small, stiff wire through the bottom of the box and bent it into place so that the chest would attach to the back end of the truck. The bent end of the wire is held in place with glue and tape. 

       Then I lined the inside of the toy box with scrap fabric and white school glue. The out side of the truck trailer is wrapped with blue foam attached with hot glue and the bottom with black tape.

       I made a set of back wheels for the trailer by hot gluing two buttons to the ends of a wooden skewer through a small cardboard tube. Then I hot glued a metal snap to the white buttons to mimic tiny hubcaps.